CARPET INSTALL SALT LAKE CITY – Carpet Installation …

A lot of people in SLC try these services on their own. We have seen it too many times and unfortunately, it does not usually go as well as planned. That's why we always say: "Let the professionals do it". We are one of the most affordable companies in the Salt Lake valley and we can do it just perfectly. Our services are impeccable and we will do all we can to guarantee your satisfaction.Our quality comes from the way we dobusiness. We have been working in the Salt Lake area for years and our clients know it well. We are methodical and follow all the steps to make sure perfection is achieved. Carpet flooring is not very simple and a poor job may look nice for a year or maybe even two, but then you notice that your carpet is loose and some ends are starting to detach from the floor.

That's when you know the job was not done properly. Few companies out there will provide an excellent service and we are proud to say we are one of them. We have mastered carpeting through training, practice and years of experience. You may trust us with your installation and you will not be disappointed. Besides installing carpets, we also repair and stretch used rugs so you don't have to replace everything. Luckily, we are near you!You will find below some of the steps we take while installing, repairing or stretching your carpets. It is worth checking.

We start by removing (when applicable) your old rug. Sometimes they come off easily and sometimes it takes a couple of men pulling them out. You would be surprised by the dirt, bugs and some other things we find underneath old tapestry.Once the removal is complete, we will dump all that unwanted, unpleasant to look upon and smelly old rug far, way far from your house. Just the feeling of getting rid of that will make you smile. As we confirm there are no remains on the floor we start cleaning. All that debris is swept away and vacuumed. The surface must be smooth and free of dust.Sometimes it is required to remove doors depending on the area being carpeted. This facilitates the process and ensures quality. Don't worry, we will put them back together and you will not even notice they were once removed.

Now that the cleaning is finished and that the doors are not on the way we start measuring. Measuring has to be done precisely. You do not want to cut your new mat a little too short and then have to patch it all over. We also don't cut it too long or too wide because that makes handling difficult during the installation process. Once that's accomplished, we are ready to start working on the Tack Strips or Carpet Grippers. If you are familiar with the terms, that's great! If you are not, these grippers are used to hold the tapestry as the stretching procedures begin. The grippers are placed along the walls and they contain nails that hold the tapestry. This prevents the mats from moving as they are being pulled across the floor.We are finally ready to bring the carpets in but this is just the beginning of our jobs.

We will lay it all out on the floor and manually stretch it as much as we can. We will then start trimming any excesses. We use a special tool for that. If you are planning on doing it by yourself, take a breather, check the phone number by scrolling or sliding up and call us. We don't want you to use scissors to cut the carpet because we don't want it to look bad. Now that you made up your mind and called us, we can proceed! It is likely that we will be using a wall trimmer. These tools work really well but they are even better when used by professionals in our team! Remember, we are here for you! Other tools will also be used during the process of attaching that first edge.The initial part is complete and now we move on to stretching the carpet (yes, once again) across the floor. This time, however, we will be using another tool called Carpet Stretcher. This tool is a mechanical tool that extends from one wall to another. It has many nails on its head that grab the carpet firmly. There is also a lever attached to its head and when the lever is pushed down, the mat is stretched tightly.Most installations also require seaming the edges of carpets when they meet each other. This is a very delicate part of the process. If not done correctly, the joining of the rugs may become noticeable to the eye. Some common issues with seaming may include not proper cutting and weak gluing. In some installs, we use a seam binder to cover the transition from one carpet to another. Bar binders are most commonly used when the mat joins a different type of floor. These binders are usually made out of a metal such as Aluminum but sometimes they can be made of wood. Some specific tools are required for the task such as a cutter, a seaming iron, seaming tape, hammer, and many others. Attention! If you ever use a seaming iron, make sure you are cautious. Its temperatures may reach well above 400 degrees. Let's avoid getting hurt or hurting someone by always putting safety first and following best practices.

Now that we know those edges were seamed together and that no one can tell where the rugs join, we can start the final steps of the install. The final steps also require some of the tools that we already used. Trimmers, carpet knives, power stretchers and so on.Looking at the floor is now delightful! We did a great job but there could be some imperfections still. That's why after we are completed, we perform an extra step which is a full verification of the job. We walk around every corner and check if the trimming was proper. We also make sure the edges are all looking good, especially around the vents on the floor. The job is considered completed when it passes all the verification procedures. Salt Lake City Carpet Install will deliver what was promised! You may now enter your house!

The rest is here:
CARPET INSTALL SALT LAKE CITY - Carpet Installation ...