Home Builder Developer - Interior Renovation and Design

Drywall or sheetrock is the gypsum product used to replace the lath and plaster method of covering a wall in preparation for paint, wallpaper, or other finishes.

How much it will cost to install depends on if you are installing new board or replacing old or damaged drywall, how much labor costs in your area, and the level of finish you want with your installation. The cost is usually in the $1,000 $2,500 range.

Typically, sheetrock costs $1.25 $3.00 per square foot to install. A small area will cost more than a larger area per square foot because the contractor will still need to pay for transportation, permits if required, etc. However, once you add in all the other materials, like joint compound, drywall screws, tape, and labor, it could cost as much as $40 $50 for each full-size sheet.

After determining the dimension of the area you want to get covered with drywall, and you know how much you pay for each panel, enter those figures into our handy drywall calculator. It will tell you how many boards and materials you will need to buy. Lets say you have a 10 x 12 room with an 8 ceiling and the ceiling needs drywall too.

Once you put that information into our calculator and click on calculate, you will see that you need 15 sheets of 4 x 8 drywall, three pounds of screws, three rolls of 100 tape, five gallons of lightweight ready-mix joint compound to cover the 472 square feet. So, using the square foot figure, it will cost $590 $1,416. Just $300 of which will go toward the drywall panels.

If you have the time, tools, knowledge, and some assistance, you can do this as a DIY project. You can usually get a better deal on 4 x 12 sheets and then cut the sheets in half, especially for the ceiling where you will have to hold the panels in place at least long enough to get a few screws in it. If you have never installed drywall, you could check out some YouTube or other DIY videos, or when you need it done right the first time, contract an installation team.

Now all you need is an installer, right? Get free estimates by entering your zip code on our Find Qualified Drywall Professionals in your Area page. But, before you run off to find installers, you will need to tell them what level of finish you want for your install.

Most people have no idea there are different levels of finish when they tell the contractor they want drywall installed. Well, they might consider they want the wall ready to paint or cover with wallpaper. There are six levels, but only five provide any type of finish. At level zero, you will only get it installed and nothing more.

This is the most expensive option and requires the least amount of work by the homeowner. The customer usually needs to specifically ask for this level, because on top of the three layers of joint compound, the drywall gets a light coat as well. The intent is that nothing shows through and paint doesnt sink into the board.

Level four gets three coats of compound, but the board itself does not get coated. This level is best when the owner will prime the walls before painting.

This level is acceptable for heavy texture with just two coats of the compound but should not have any tool or ridge marks. This level is suitable for wallpaper.

This level usually is appropriate for areas you dont intend to finish, such as a garage or unfinished basement. You will get one coat of compound. This level is also useful when you intend to add tile.

Joint compound will cover the tape and not much more. This is good for rooms you dont intend to use such as an attic or water heater closet.

With this level, you will get your drywall hung. Nothing gets covered, no tape, and no compound. This level is acceptable for a low-budget DIY project when you wish to finish the room your way.

The higher the level number, the more work is required; therefore, the more the contractor will charge to finish your drywall project. When you get to that step in the finishing process, consider our room paint calculator or room wallpaper calculator. Considering how much each will cost, will give you a better idea which finish level to choose after examining your total budget.

We suggest getting several estimates for your project to find the contractor to work with that meets your budget and project requirements. You can find contractors online, or alternatively, you can ask your citys building inspectors office or the Better Business Bureau.

All pricing information on this page is based on average industry costs, and is subject to variance for project-specific materials, labor rates, and requirements.

Link:
Cost to Install Drywall in 2019 - Inch Calculator

People sometimes use the terms sheetrock and drywall interchangeably, but they are not exactly the same. Drywall is the industry term for prefabricated sheets of wall, while Sheetrock is the brand name of a type of drywall. Depending on what room is being built, your drywall installation pro will select different thicknesses or grades of drywall. Standard residential drywall is -inch thick. Garage walls adjacent to a living space are typically -inch thick and serve as a firewall. For a garage ceiling, most contractors will use firewall-grade drywall materials to keep your home as safe as possible.

Different types of drywall can be color-coded to indicate their purpose. Purple or green drywall boards are often mold-resistant (MR) and are applied where moisture tends to accumulate, such as in bathrooms and basements or behind tile backsplashes at sinks. These mold-resistant sheets have a fiberglass instead of a paper facing finish to prevent water absorption. Regular drywall is gray or white. The drywall industry is constantly adapting with technology to provide safer and more targeted materials. You can even install soundproofing drywall to help prevent noise transfer through rooms.

Follow this link:
The 10 Best Drywall Contractors Near Me (with Free Estimates)

Home > Home Improvement > Drywall & Insulation > Drywall Cost

Drywall, also known as wallboard, plasterboard, or sheetrock, is widely used in the construction of interior residential walls and ceilings. Made from sheets of pressed gypsum (gypsum is a type of mineral), drywall took the place of plaster as a wall-building material in the mid-twentieth century.

Drywall is mass-produced and therefore cheap. It's also easy to install and simple to repair, even as a DIY project. Professional drywall installation costs more, but a pair of pros can finish an entire room in an hour or less. If you've never worked with drywall, all you need to tackle the job are a few hand tools and some patience (getting it right takes practice). A how-to guide also wouldn't hurt for the first-time drywaller. The following resources should provide all the information you need to hang "rock" like a pro:

Drywall was a big step up from plaster, as it provided a much faster way to cover ceilings and walls. But the material does have one weakness: it's easily damaged. Wall-hangings, doorknobs, and overzealous children are common causes of broken drywall, although there are endless ways that damage can occur. Cracks and nail holes can be fixed with joint compound alone, while more extensive damage requires buying a sheet or two of drywall and some tape. As with installation, hiring a pro is faster but costlier. If you're intent on performing the repair yourself, these sites are a good starting point:

Whether you plan on installing or repairing drywall yourself or hiring a pro, keep the following points in mind:

See the original post here:
2019 Average Drywall Installation Prices: How Much Does ...

Properly installing drywall requires a steady hand and a sharp eye for detail, but its also one of the least-expensive projects in home building and remodeling. Drywall offers a lightweight, cost-efficient material for interior walls and ceilings, which are undoubtedly some of the most important structural and decorative elements in your home. Although the framing provides the structure and support, drywall is the crucial final addition that gives you smooth, even walls that form the ideal canvas for the rest of your home decorating ideas. Read on to learn more about the process of installing drywall and the average costs of the materials that go into this project.

If you need help with your drywall project, let ImproveNet connect you withlocal drywall professionalsfor free.

Homeowners spend an average of $1,500 to buy drywall, with prices that average of $0.30 - $0.35 cents per square foot for the drywall and other materials needed for this project. The amount you can expect to pay to drywall a room or a home depends on a variety of factors. Before you start pricing materials, take advantage of our drywall calculator and estimator to determine the number of sheets you need for your project.

To calculate your estimated drywall cost, take the number of sheets you need and multiply it by the cost of the drywall sheets, which usually price out at around $6 each. Other costs to consider include materials such as:

When you're estimating drywall costs, you need to calculate your square footage, and then consider the size of the drywall panels you want to use. Drywall most commonly comes in 4 by 8' sheets, with thicknesses ranging from -inch to -inch. Thin, -inch-thick drywall sheets are ideal for damaged areas during repairs, but they aren't strong enough to use alone.

Standard sheets are -inch thick and weigh 57.6 pounds. Thicker, -inch drywall usually is made of fire-resistant materials. It's ideal for firewalls or anywhere you want added strength, including ceilings, although its around 20 pounds heavier than -inch-thick drywall.

Most people use 4' by 8', -inch thick, standard-sized drywall sheets for small and medium drywall projects. Some of the common sheet sizes and average prices to give you an idea of how much drywall costs include:

When you install drywall, you also finish it to one of six finish levels. The level you choose depends on the wall's location and the preferred finished look. The levels include:

Start by installing the ceiling drywall. Have someone nearby to help you hoist and hold the panels in place with the edges perpendicular to the joists and one end snug against the wall. Insert five evenly spaced screws along the width of the panel into the joist closest to the center of the panel, keeping all screws at least -inch from the edge of the panel. Repeat the five-screw installation along each joist, adding additional panels as necessary to create a row that reaches the opposite wall. Continue working in rows to complete the ceiling installation before beginning the walls. Work your way around the room, placing and securing the drywall panels until the room is complete. Then you can add tape and joint compound to finish the process.

Fastening screws offer a secure hold that doesnt pop out as easily, making them particularly ideal for use when you drywall a ceiling. Use 1-inch screws and a screw gun that's adjusted so you drive the screw into the drywall just far enough to leave a light recess for the joint compound to cover. Insert screws 12 inches apart in the areas where edges of the drywall panels meet at wall frames.

Drywall nails offer a good, secure hold for hanging drywall on walls, and theyre easier to install because you only need a hammer, which makes the process a bit faster. Choose ring shank nails that are at least 1-inch long. Depending on the building codes in your area, you may need to install drywall nails every 6 to 12 inches to hang drywall.

Many pros use a bead of heavy-duty adhesive along the frame of the wall to prevent nails from popping and add a more secure hold. Apply the glue to the wall or ceiling frame, press the drywall panel in place and fasten with nails or screws as desired.

Although drywall can be a DIY project, consider where you're hanging the drywall before you decide to do it yourself. If you're hanging drywall in the garage or in a utility room that doesn't need to look perfect, you could try your hand at hanging drywall. If you're building a home, repairing a ceiling or performing major renovations, consult a professional. In addition to finishing the job quickly, pros have the skills necessary to give the drywall a seamless, smooth finish.

Hanging drywall yourself can end up being much more expensive and time consuming than hiring a pro. Why go at it alone? Head to our free drywall lead generator to connect with local professionals with the skills and experience to help you get the job done.

Last updated on Nov 8, 2018

Link:
2019 Drywall Installation Cost | Cost of Drywall | Sheetrock

The average cost to install drywall in a 1212 room is $450-700.

The biggest factor that will impact your total cost is wall size. Others are type of drywall used, and complexity of the work involved.

Contractors use drywall in homes and commercial spaces to construct wall and ceiling surfaces. It is also known as wallboard, sheetrock or gypsum board.

Across US homeowners report spending $1.5-2.2 per square foot to install drywall. This includes all materials and labor to both hang and finish the drywall, so that a contractor can paint it.

If you have about 2,000 sq.ft. of wall space, your total price for new drywall will be about $3,000-4,4000. This estimate is for a simple rectangular room, without any complex architectural details, multiple corners or any other obstructions that would need to be worked around.

Contractors should use the longest possible drywall sheets, as this can save money on both materials and installation time.

Your total install price will go up depending on the size of the job.

Most contractors have different rates based on the number of drywall panels being installed. You can get a lower price per sq.ft. on a project that uses at least of 50 sheets of drywall or more.

For example, if you have a space of about 2,400 sq.ft. and will need to cover it with 50 12 sheets, the cost will be about $72-84 / sheet, or $3600-4200 total.

However, if you have a room that you need to put drywall in or a space under 400-500 sq.ft., your cost per sheet will go up to $100-120 or more.

If you have a huge mansion or a commercial space (over 10-12,000 sq.ft.) you can get a significant discount on the total drywall installation cost. It can become as low as $1.15-1.25 per sq.ft.

Its important to keep in mind that labor rates also very greatly by region. In affluent cities such as Boston, New York, San Francisco you can be paying as much as 20-30% more than the national average. By contrast, less well-to-do regions will have prices that are about 10-15% less than the national average.

To get the best price, be sure to contact 3-4 local drywall pros and compare their quotes.

There are different types of drywall available, and they all have different prices.

Standard drywall of various thickness (ranges from 1/4 to 5/8): costs $0.24-0.41 per sq.ft, depending on the thickness.

Moisture-resistant drywall: costs $0.40 0.48 per sq.ft.Heat/Fire-resistant drywall: costs $0.34 0.42 per sq.ft.Sound-barrier drywall: costs $0.95 2.25 per sq.ft.

Note, sound resistant drywall costs the most to install, as much as $4 and up per sq.ft. for labor and materials.

Here are some additional things that a contractor may need to do and charge you extra.

1. Remove and dispose old drywall: if you need to remove old drywall before installing new one, be prepared to spend! This work is very expensive, ranging from $2 -3.25 per sq.ft. This is one area where you can try to save money, if you are willing to do this job yourself.

2. Scaffolding: if your house has very high, cathedral or vaulted ceilings, installing drywall will be a lot more challenging and will require scaffolding. Depending on the contractor, you may get a 30-50% up-charge on the total.

3. Complex architecture: if your home has many corners and arches that a contractor will need to work around, the total cost can double or triple. Similarly, costs will go up if he will have to work around built-in shelves, countertops and kitchen cabinets.

4. Smooth Ceiling: if you install ceiling drywall and want the texture to be completely smooth, you will pay a premium charge. To create a perfectly smooth ceiling a pro needs to spend a lot of time applying many coats of mud and the sanding the surface.

By contrast, a textured ceiling is significantly cheaper. This is why many people prefer it over a smooth one. To create it a contractor applies only one coat of mud, after he seals the joints.

Read more from the original source:
Drywall Installation Cost Estimate Prices To Hang Drywall ...

Vertical Only, heres the proof & truth!

Why and How Horizontals Wrong (and why Verticals right)...dont ruin new from the start:

1 Defective Seam - Horizontal rows needing more than one drywall panel creates (instead of avoids) butt-joint humps, which are not flat and are a twice (minimum) the effort defect. Outlet and switch cover-plates, window and door trim, baseboards, pictures, mirrors and cabinets dont sit flat. Using any "butt-joint product" erases all "claimed" benefits of Horizontal!

2 Unsupported Seam Horizontals tapered edge is 90% unsupported, only 10% (instead of Vertical's 100%) contacts framing, the seam will and does crack. Light switch and countertop electrical boxes within the seam equals more weakness and butt-joint doubled, minimum, efforts.

3 Structural Defect - Horizontal only reinforces a wall height of 4 or less, a full-height wall's top-plate is never connected to the bottom plate. As in and due to #2 above, Frictional Contact is minimized (instead of maximized by Vertical).

4 Seam Deception...4'x8' Panels Example 1: 48 tall by 102 long wall, Horizontal = 48 (technically) and its a 24 wide butt-joint or a minimum of doubling the 48" (Vertical = the same, generously, 96 but theyre easy 6 wide joints). Example 2: 96 tall by 102 long wall, Horizontal = 222 with 50% being 24 wide butts (Vertical = 192 of 6 wide easy joints, yes less)...in a Kitchen Horizontal = 100% of 24 wide butts (Vertical = 0%). Yes, Horizontal does the taper area twice (minimum) in order to hide its butts, so very minimally just another 24 was added and #5 below was not factored into Horizontal's monumental fraud.

5 Self-Defeating Angles Horizontal only uses one of a panels tapered edges and puts the other taper at the ceiling corner and baseboard creating (instead of avoiding like Vertical) a twisted angle that must be shimmed or additionally mudded. This too, instantly erases all "claimed" benefits of Horizontal by doubling the seam amount, patching itself to equal Vertical!

6 Unfriendly Seams Horizontal celebrates the chest height seam and pretends theres no 24-wide floor to ceiling butt-joint and the ever present baseboard bevel of unfinished work. (Vertical has easy joints and the top's screwed, taped and mudded later with the ceiling corner and the baseboard spots can also be done separately).

7 - Fire Hazard Liability - Horizontal only fills the coin-thin seam's face and has no back blocking, causing smoke and fires spread by inviting fuel air for a fire's growth (Vertical is full depth and airtight once simply screwed-in).

8 - Unsafe Installation - Horizontal needs 2-people for a safe installation and the panel is airborne, literally creating the chance to cause injury (Vertical easily tilts-up with just 1-person). Using a panel lifter isnt even as easy and safe as Verticals tilt-up.

9 - Additional Waste - When correctly covering a knee wall, half wall, tub front, column or soffit by first removing both tapered edges, Horizontal can't use the tapers elsewhere (Vertical can and does). And, Horizontal wastes 4-times the mud on their completely unnecessary butt-joints and baseboard bevels...if ever done.

10 - Destructive Ignorance - Foundation and Framing crews go to great pains to make everything flat, level, plumb and square. Horizontal destroys those efforts with their defective humps and baseboard bevels (Vertical keeps the perfection).

11 - Grasping At Straws with Outright Fraud - Horizontals falsely and unknowingly wave the absurdly invalid (FPL439) 1983 testing Contribution of Gypsum Wallboard to Racking Resistance of Light-Frame Walls by the self-convicted fraud Ronald W. Wolfe. FPL439 found that all tapered paper wrapped edges must be fully intact for Horizontal to beat Vertical, period. In the real-world, Horizontal's bottom paper wrapped edge is removed by law, for spacing from all floors and thereby completely negate Wolfes inexcusably deceitful and worthless "study" (laughable) and summation.

12 - Joint or Seam Treatment - According to the ASTM's C840 8.2, Horizontal's seams must be mudded to provide any fire, smoke and air travel resistance (Vertical's so good that it's not required to have its seams treated at all).

13 - Costly Slow Complication - Horizontal's depend upon pricey special muds and even messy tape or taping tools that waste mud. Taping tools still require a 2nd step of knifing the tape and the muds require a mixing step. That's more expense, more time, more tools and equipment and more water...for an inferior job! Vertical's superior with the cheapest ready-mix bucket muds and dry self-adhesive tape. Again, Vertical's seam treatment is just for looks.

14 - Fire Rating Fail - Most Single-ply or Single-layer drywall for Commercial Work is required to be installed Vertically, to obtain drywall's actual rating. This is well-known by the majority of Horizontals, but you and your children don't matter to a Horizontal. And for what, to honor the frauds that taught them wrong? You've now seen that Vertical's faster overall and immensely better in every way.

Only promote Horizontal as wrong and confidently cite the above incontestable facts.

Continued here:
finishing - Should drywall be hung horizontally or vertically ...

Drywall is one of the most prevalent materials throughout our homes, and its susceptible to damage. Moisture, wall decorations and general wear can add marks, holes and otherwise damage your drywall over the years. Your local Mr. Handyman is here to handle all of your drywall installation services and repairs, from your big renovation project to drywall repair and finishing.

Our expert home improvement professionals can also install drywall in your new home or addition. First, well prepare for drywall installation by measuring the area and covering electrical wires and plumbing with proper protection. Our installation services include measuring, cutting and hanging drywall or Sheetrock to your exact specifications. When thats done, well double-check the walls to make sure electrical boxes and other features are perfectly framed. Then well apply any finishing touches you need, such as painting.

Has moisture damage or years of wear made your walls look drab? If your drywall is damaged beyond repair, our home improvement professionals will gladly refresh your home with needed drywall replacement. Reach out to your local Mr. Handyman, and we can schedule a convenient time to come in and get started on your new drywall installation.

The best part? Our handymen have a wealth of services to offer before or after your drywall is installed, such as painting your room. We even offerwainscoting installation and repair. And keep in mind after were finished hanging your drywall or touching up, we canhang your paintings for you, as well as your TV, clock, artwork or animal mounts.

From major home remodels to minor drywall replacements, no job is too big or too small for Mr. Handyman professionals. So if you need help finishing your home drywall project or want an experienced professional to complete the project from start to finish,your local Mr. Handyman is waiting for the call.Request an estimate today, or call 877.685.1377 to get started.

See the original post:
Drywall Installation | Mr. Handyman Drywall Installation Services

Stress Cracks

If you've located a stress crack in the sheetrock of your home or office, our experts can help you determine the best course of action. We can remove and replace the stress cracked drywall, paint them if necessary and return your wall or ceiling back to their original condition.

The most common problems we encounter are holes in walls and ceilings. Our professional crew will help you determine the safest and most cost effective way to repair the holes or replace entire sections of walls and ceilings. When we've finished, they'll be seamlessly repaired, painted and look as good as new.

If you're adding on to your home or finishing a basement, we also offer new drywall installation and finish work from frame through finish. We mask the work area to protecting floor surfaces, move your personal items out of the work area, and build dust control tenting as needed.

See the article here:
Drywall Installation & Repair | Services | The Honey Do ...

This article is about how to install a drywall ceiling, either on wood or on metallic frames. The most difficult part of this project is to lift the drywall boards. You could rent a drywall jack, or ask another person to help you hang the drywall boards. However, if you choose to build a metal stud frame, the process will take a little long, but the quality of the project will be extraordinary. Installing a drywall ceiling is not difficult, provided you use proper tools and materials and understand the basic techniques. Remember that you have to install the sheets of drywall perpendicular to the direction of the joists.

Although installing a drywall ceilingis not an easy job, with the help of another person virtually any experienced diy-er can finish such a project. The most difficult stage is to lift the drywall boards up to the ceiling, while the rest of the operations are just common-sense. Therefore, you can either rent a drywall jack for several days, or use a ladder and ask a friend to assist you. If you dont afford to rent the drywall jack, you need someone to hold the sheet into position, while you drive in the screws.

As you probably now, drywall panels come usually in the following dimensions: 4x8, 4x9, 4x10, 4x12, with a thickness ranging from 1/3 inches to 5/8 inches, but the most commonly used drywall boards are the 1/2 inches and 5/8 inches thick. Read carefully our article and you will learn the skills required to hang a drywall ceiling in a professional manner. If you are not prepared to work by yourself, consider hiring a qualified contractor, even though this will increase the cost of your remodeling project.

Drywall ceiling layout

Before installing the drywall ceiling, you have to understand thatyou have to use a proper layout, as to get the job done in a professional manner. Consequently, you have to start with one corner of the room, by using a full drywall board.

The next row of drywall must start with half of a drywall sheet, as to create a proper layout. In addition, when inserting the screws make sure you observe the right spacing, as to secure the boards properly.

Metal stud ceiling frame

The first step of the project is to evaluate the structure of the ceiling, made of either wood studs or of metal studs. As you can see, in our case we will install the drywall ceiling on a metal stud frame, but you can install drywall boards on wood studs, as well.

The first thing you have to evaluate is if the ceiling frame is level. This aspect is very important, as otherwise the ceiling wont have a pleasant appearance and in time the joints between the drywall boards will crack.

Installing polyethylene vapor barrier

After we have made sure the ceiling frame is level and secured properly, weve decided to install mineral wool insulationand an anti-vapor foil, for both saving energy and ensuring a long lifespan for the drywall ceiling. The anti-vapor foil can be installed on a double adhesive tape or can be locked with staples. The main aspect is to make sure the foil is fixed properly and it doesnt make folds.

Work with patience and make sure your ladder is installed on a level surface.

Installing drywall on ceiling

When installing the drywall ceilingstart from a corner, making sure the boards are as close as possible to the walls. If the corners of the room are not right angled, you should cut the drywall panels as to fit perfectly into place.

All edges of the drywall boards should be fastened to the ceiling studs. When connecting two drywall boards, you should screw them on the same stud, the joint line being exactly over the studs median. Lock the drywall boards into position with several screws, along edges and in the middle.

Fixing the drywall ceiling with screws

Afterwards, continue fastening the drywallwith screws, using an electric screwdriver. If you install 1/2 drywall, then you should use 1-1/4 drywall screws, as if you are installing 5/8 drywall a better option would be 6 x 1-5/8 screws.

This size of the screws is very important, as the rigidity of the ceiling is also based on the type of screws you are using. Along walls, we have installed screws every 7/15 cm, while inside the boards we have installed the screws every 12/30 cm. Dont insert the screws too close to the edge of the drywall panels, but leave around 1/2 to prevent cracks.

Drywall ceiling joints

After you have installed the first drywall board, you should continue with the next boards.Therefore, work with great care to make sure you align them properly.

Drive in the screws, as to make sure their heads are aligned with the drywall surface. In order to make a proper job we recommend you to use a screwdriver with torque control, as you can adjust the speed.

Installing drywall ceiling boards pattern

When installing a drywall ceiling, you have to use the stretcher bond pattern. Therefore, you have to start the the next row with half of a drywall board and continue it with full boards.

In addition, you might have to cut several holes in the drywall boards for smoke detectors, for electrical wires for light fixtures of for ventilation appliances. In order to get the job doneprofessionally, you should use a drill machinery with torque control and masonry drill bits.

Installing drywall ceiling

Continue installing the drywall boards in the same manner described previously. When installing a drywall ceiling it is important to follow the layout, otherwise it wont be durable.

Finishing drywall ceiling

After you have installed the drywall ceiling, you have to finish the joints by applying putty and drywall paper. This step is not difficult, but it is essential for a neat look.

Therefore, you should cover the screw heads and the drywall board joints by using a large trowel, paper tape and drywall putty. Remember that you have to apply at least 2 layers of putty. After you have applied the putty, you have to sand it a couple of times (using at first medium grit sandpaper and then fine grit sandpaper), until it will look properly.

Cutting drywall

In order to cut the drywall boards, you should mark the exact dimension on the plasterboard, using a pencil and a T-square. Use a tape measurement, to make sure you make accurate marks on the sheet.

The next step is to use a sharp utility knife and to go several times over the drawn line, as top make sure you have cut it deeply. Bend the board alongside the cut and split the two drywall boards by cutting the paper layer with a utility knife.

Thank you for reading how to install drywall ceiling, and we also recommend you to read the other articles, related to drywall ceiling. Please LIKE and SHAREour articles using the social media widgets. SUBSCRIBE to be the first that gets our latest projects.

Read the rest here:
How to install a drywall ceiling - Step by Step

Are you dreaming of a new kitchen? Better Than New Kitchens can provide you with a full range of ideas and options for kitchen refacing. You will be amazed at what a difference updating one of the most important rooms in your home can make. According to statistics from the United States Department of Labor, Americans spend between 700 and 1,000 hours a year in their kitchen. An epicenter of activity, from day-to-day use to entertaining family and friends, the most used room in the house deserves your attention.

By simply refacing or refinishing your kitchen cabinets, you can give your entire kitchen a face-lift without the expense of a total renovation. Refacing and Refinishing are cost effective and professional alternatives to tearing out your kitchen and starting over. The average cost of a reface is less than half the cost of a new build project. We can also build you a new island or add more cabinets to give you extra storage space.

Better Than New Kitchen Reface with Solid Alder Wood Shaker Doors, Gray Stained Finish and custom island facade

Better Than New Kitchens uses the highest quality woods and finishing products in the industry. Every kitchen reface is installed by the owners themselves with over 25 years of experience in custom woodworking and finishing. Better Than New Kitchens guides you through designing the look of your kitchen, where you get to choose it all the door style, drawer style, species of wood and custom finish. Using our fine materials and expertise, Better Than New Kitchens provides the highest quality cabinet refacing in Scottsdale and Phoenix.

Paradise Valley White Shaker Cabinet Door Reface with Custom Built Island

Scottsdale Kitchen Reface with Dark Chocolate Glazed Antique White Raised Panel Doors

See the original post:
Kitchen Refacing Will Transform Your Home