Home Builder Developer - Interior Renovation and Design

Edit Article

You will thank yourself a million times over for choosing tankless water heating. Be aware that there will be a slight delay for the hot water to arrive at your fixtures and that the money saved in standby loss is offset by the higher cost of equipment, gas pipe, flue pipe and materials.

1

CAUTION: Tankless water heaters generally require larger diameter gas supply lines, higher voltage power supply (if contemplating electric on-demand), dedicated - special stainless steel flue (known as Category II, III or IV) or larger diameter exhaust system. Please take these things into consideration before you decide to DIY.

2

It is highly recommended that you use special union connector sets for the water supply which employ bypass capability. This will allow for simple, easy de-liming maintenance process in the future.

3

Turn off main incoming water line to house.

4

Disconnect supply line from old water heater. You will probably have some water left in the line even though your main has been shut off. Place a bucket underneath water bib to catch any spills.

5

Disconnect heat source from old water heater as follows: for gas, (propane) make sure the supply valve is closed (this is usually determined by the direction of the handle to the valve sitting either in the same direction as the line "open", opposite the direction of the line "closed"). For and electric water heater, simply unplug the appliance from the wall outlet.

6

Once you have completely disconnected the old water heater you must remove it from it's current parking space and make sure to dispose of it according to the laws in the area you live in.

7

Remove your new tankless water heater from the carton and place all hardware and instructional material close at hand.

8

Determine the location best suited for this appliance and make sure you have allowed for the proper clearances around it to comply with all state and local building codes.

9

Mount tankless heater on wall according to manufacturers instructions, making sure that you have appropriately supported its weight.

10

Now you're ready to hook up all the connections.

11

If you have gas, install ventilation ducting. Typically tankless water heaters requires larger flue or special stainless steel flue.

12

Begin with the supply line (water line).

13

Next should be the heat source. If your water heater uses electricity, plug it in to the wall.* If your water heater is gas, you will need to hook up a gas supply line from the stub at the wall to the new water heater. Open the valve so that the handle is in the same direction as the line.

14

Following manufacturers directions, light the pilot on the gas water heater.

15

Now go to your favorite shower location and enjoy an endless stream of hot water. All that work was well worth it!

Do I need to mount a gas tankless heater upright, or can it be laid on its back?

wikiHow Contributor

As with any gas appliance, heat rises so the unit needs to be mounted upright and leveled.

After I install this, will I have hot water immediately?

wikiHow Contributor

Once installed the unit will provide hot water in accordance with its rated "rise time." You will probably notice some lag between opening a hot water tap and the water from the tap being hot, similar to having a tank-style heater. The hot water still needs to get from the unit to the tap.

If my tankless water heater is gas and I have a 1/2 inch gas line to the unit, will it work for a year and then have a problem?

wikiHow Contributor

It depends on what kind it is. If it is an under-$200 tank then yes, but if it is over that price then no, it will be over 2 and 1/2 years until you should start noticing any problems.

What do I do if I have a recirculating pump?

wikiHow Contributor

Tankless hot water heaters are "on demand," and cannot be used for recirculating systems.

How can I insert batteries in the geyser?

wikiHow Contributor

If you were to put batteries inside the geyser, they would most likely burn out because it would be so warm. Plug it into a wall or somewhere instead.

Ask a Question

Thanks to all authors for creating a page that has been read 229,894 times.

YesNo

Visit link:
How to Install a Tankless Hot Water Heater: 15 Steps

Obviously you need drywall panels 🙂 There are many kinds of panels designed to satisfy various requirements. Before you start think about what you want to achieve and buy what you need for your goals. Drywall panels are manufactured in various sizes, thicknesses and using different materials for different purposes.

Drywall compound is used to fill the gaps between the drywall sheets. You can buy premixed ready to use compound.

Drywall tape is used to reinforce the compound applied on the drywall joints.

Shims are needed when the wall frame behind the drywall is less than perfect.

Inner and outer corners need special care and the best way for quality results is to use metal profiles.

Now that you have the full list of materials and tools needed for your drywall DIY project it is time to start planning and calculating quantities. Good luck!

Support this work, share it with friends ...

Read the original post:
Materials and Tools for Drywall Installation | Handy Owner

Americas Preferred Home Warranty is dedicated to helping families lessen the burden of unexpected expenses by paying towards the repair or replacement of any covered appliance or home system that malfunctions under normal conditions of use. A homewarranty can protect you in case of a major failure within your home; such as with kitchen appliances, plumbing, furnace, air conditioning, septic, roof, water heater, trash compactor, water well pump, attic and exhaust fans, electrical systems and more. Regular maintenance is essential for keeping a house functioning, but occasionally a malfunction can occur that requires repairs or replacement to restore the situation. Your Americas Preferred Home Warranty agreement will assist with the cost of large, unexpected repairs required when any covered systems fail due to normal wear and tear.

Our home warranty agreement covers a range of property types including new construction, multi-family units, and condos. We are the only company, among the nations leading home warranty companies, that allows you to choose your own contractor for all covered repair work.

Americas Preferred provides quality coverage to properties across the United States of America. Gain peace of mind in knowing you are protected against the unexpected failure of major systems within your home. Real estate professionals understand the importance of protecting your assets for the future.Our team currently works with customers in AL, AK, AR, AZ, CO, DC, DE, GA, IA, ID, IN, KS, KY, LA, MD, ME, MI, MN, MO, MS, NC, ND, NE, NJ, NM, OH, OR, PA, RI, SC, SD, TN, & WV.

Original post:
Home Warranty | America's Preferred Home Warranty

Table of Contents

Just like your countertops or floors, you have plenty of options when it comes to gutter installation. Combined with the fact that many gutter professionals charge different amounts, the variety of options makes the average gutter installation cost quite volatile. Nevertheless, after analyzing over 12,000 gutter projects, the average cost to install gutters is $850. Bear in mind, we have seen gutter installation prices soar up to $2,000 for more extensive projects.

If youre replacing your gutters, your gutter project cost should not change too much, but you keep the following in mind. First, to install new gutters, you or your pro will have to remove the current gutters. Many homeowners can handle this project without a pro. If you do hire a pro, expect to pay $150 for removal and disposal. Second, you may be able to save on your gutter installation price if youre replacing since you can save on some materials. This of course assumes youre adding the same type of gutter.

Finally, you may be able to get a discount if you hire the same gutter company to replace your gutters that installed them in the first place. Gutter pros love repeat customers and usually offer rebates to rope them back in.

A majority of your gutter cost will come from materials and labor. When budgeting material costs to install gutters, its important to first have your contractor map out lengths and the location of downspouts. Gutters are generally sold in prefabricated lengths of five, 10 or 15 feet. Downspouts come in various sizes as well. While most of the gutter installation cost will come from labor, its still important to assess all possible material costs ahead of time. As well get to later, gutter material costs range from $4 to $25 per linear foot.

Most of your gutter installation cost will come from labor (if you hire a pro). If you do hire a gutter contractor, expect to pay at least $400 in labor charges. While you can install gutters on your own, one mistake can lead to flooding or serious injury. Therefore, many homeowners bite the bullet and hire a local gutter contractor.

While materials dont take up a majority of your gutter replacement cost, they can vastly alter your gutter budget. As such, it pays to know the average gutter material prices across the country:

If you want to keep costs down and try to install your gutters on your own, give vinyl a try. Theyre affordable, light, easy to install and come in a variety of colors. However, that low price point does have one major drawback. Sadly, vinyl gutters and downspouts are not durable in cold weather. In fact, they can snap when temperatures get below 10 degrees Fahrenheit.

Steel, unlike vinyl, can hold a lot of weight. Therefore, if your house is surrounded by trees or sees a lot of rain, steel is perfect. As such, is also requires less cleaning than other gutter options. However, like all steel, it can rust. Therefore, you have to constantly check in.

Rain gutters direct water into a specific, safe location away from the home that won't do any damage.Rain gutters also prevent rain from damaging the landscapingoutside of the house. Without rain gutters, your landscape would require a lot more maintenance than it does today.

Aluminum gutters are towards the middle of the cost spectrum, yet still bring a bunch of advantages with them. These gutters are durable, can be used as fascia boards, require minimal maintenance and can withstand hard temperatures. On the downside, aluminum gutters can clog easily and crack with rapid temperature changes.

Copper is the most durable gutter type. While they are more expensive, the long timelines makes their lifetime cost less than any other material. In addition, nearly 40% of all copper used in copper gutters is recycled from prior use. On the other hand, the installation price tends to scare homeowners away. Moreover, copper is a very hot material and thieves have been known to target homes with copper gutters.

Seamless gutters are gutters that come in one piece. There are no breaks or seams in the gutters where water and debris can seep in and lead to deterioration. Theyre virtually maintenance free, but come with a hefty price.An $800 starting price is far more than any other gutter type.

Gutters do not end on the roof. Properly routed by the gutter system, downspouts create a controlled way to get the water to ground level and successfully direct it away from the home. More often than not, your gutter material will extend to your downspout. Nevertheless, if you go with a different material, please refer to costs per linear feet above. If youre buying by the piece, expect to pay:

If youd like to avoid a gutter repair bill, you should consider installing gutter guards. Gutter guards prevent debris from clogging your gutters. As said earlier, clogs can seriously damage your roof, landscaping or foundation. Repairs for all three are not small. Furthermore, gutter guards prevent ice dams. While theyre pretty to look at, they can take your gutters straight off your roof.

Basic guards ranges from $3 to $5 per 3-foot section. More complex gutter guards or guards used on intricate gutter systems start at $15 per 3-foot section.

Finally, there are four other gutter price ranges you should be aware of. The first is gutter cleaning. To prevent clogs and expensive repairs, homeowners should clean their gutters every two months (more often in summer and spring). As you might expect, cleaning is quite easy. All you need are gloves and a ladder. However, if you want to hire a handyman or gutter cleaning contractor, expect to pay $145.

The next cost consideration is repair. As you read above, most gutter types need casual maintenance. If you avoid it, your gutter could crack, rust or clog. While the cost to repair a gutter is only $315, it still adds to your overall gutter lifetime price.

If you live in colder climates, homeowners should also consider adding heat tape. This specialized tape prevents ice dams from forming. Instead, water will flow through your gutters how it was originally intended. Heat tapes start at $77 for 100 feet.

Finally, instead of gutter guards, you could buy mesh screens for as little as $1 per square foot. They not only keep leaves out, but animals as well. Again, if trees surround your home, you should consider installing gutter guards or mesh screens.

Unlike your kitchen floors, you dont have to monitor your gutters every week. However, the occasional cleaning and checkup will do wonders for your checkbook. Therefore, consider the following gutter maintenance tasks:

Gutter installation or replacement should be performed by a general or roofing contractor. The complexity of the job often depends on the size of the home as well as the height of the roof. Often, if you have high roofs, a roofing contractor will not only have better and safer equipment, but will also have more experience. Although their services may cost more than a general contractor or handyman, it may lead to a faster and more efficient job in the long run.

If youre adventurous enough to install your own gutters, youve come to the right place. The following steps should be used to install aluminum gutters. For more details, please see How To Install Gutters.

To see how the pros do it, please watch the video below:

Your gutters play a significant role in preventing your home from flooding. If you havent maintained or monitored your gutters in months, it may be time to contact a local gutter contractor.

Last updated on Mar 31, 2017

Read more from the original source:
2017 Gutter Installation Cost | Gutter Replacement Cost

Rain gutters are an essential form of drainage that help protect your property from flooding and damage. At A & J Reliable, we understand the importance of having a well-functioning gutter system. Thats why we offer specialized Rain Gutter Installation and replacement services to help protect your assets.

A & J Reliable is meticulous about the process of installing gutters. Our gutter specialists measure your roof to determine the proper gutter size for your needs. We ensure the gutter system provides adequate drainage and the appropriate number of hangers required to support the anticipated load of each gutter.

We select the appropriate gutter for your needs based on your architectural style, location and climate. One of our primary products is the commercial box gutter in galvanized steel, cooper or aluminum. Its large size makes it an option for commercial buildings needing to drain high volumes of water. We can customize your box gutter with splice plates, end caps and corners to match your selected finish. This ensures your gutter system is not only functional, but is an attractive addition to your building.

A & J Reliable has been in the gutter installation business for more than 30 years. Customer satisfaction is our overriding goal, so we are happy to provide our clients with a generous warranty on labor and materials. We have completed thousands of gutter installation projects for New Jersey and New York residents and businesses over the years, and we look forward to assisting you in this area.

Contact us today for more information about our premium gutter installation services!

Read this article:
Gutter Installation in New Jersey and New York | Gutter ...

American family uses a lot of water to maintain its landscape. In fact, during the summer months, 50% of total water use is expended on landscaping. Reducing water use without sacrificing an exciting landscape design using sand & gravel from The Yard Depot in Cypress TX can help you save money.

Decorative gravel can help you reduce the water used for your landscape design in Houston. Create the perfect balance of trees,shrubs, sand & gravel for a beautiful landscape layout of your front or back yard.

~ Basic sand that has a yellowish color to it (unscreened).~ NO NUTRITIONAL VALUE.

Recommendation: Used as a fill material, or to build a base under concrete.

~ It is classified as a fine aggregate for masonry mortar, white in color.~ It is washed and double screened to be a finer sand.

Recommendation: It can be used in mortar mix, bunker sand for golf courses, beach sand for sandboxes, volleyball courts, under vinyl swimming pool liners, and also as an option to level low spots on the lawn.

~It is classified as a fine aggregate with size less than 3/8.~Yellowish-Reddish in color.~ It is washed and screened.

Recommendation:Mainly used in production of ready mixed concrete (NOT FOR MORTAR), dairy barn bedding, backfill pipe bedding, and also as a base for pavers or flagstone.

~It is classified as a coarse aggregate.~ It is light in color, a blend of beige,tan, white, gray, & small amounts of black and red stones.~ It is crushed, washed, and screened to a size around 3/8.

~*size may vary from the picture*

Recommendation: It may be used for backfill along foundations walls, concrete subgrade (requires no compactive effort), pipe bedding, dog runs, underneath golf course greens and in ready mixed concrete for exposed aggregate concrete, and also to plant cactus: 50% Pea Gravel- 50% Turf Mix.

~ 1/4 to 2, mostly 1.5 in size.~ For used in drainage or garden ponds.~ Can be used as decorative aggregate, pathway grave.

~*size may vary from the picture*

Recommendation:For used as a backfill around underground storage tanks, and landscape decoration.

~ 2 to 6, mostly 4 in size,Brown in color.~ For used in drainage or garden ponds.

~*size may vary from the picture*

Recommendation: Used in drainage, landscape decoration & garden ponds.

~What we keep in stock is 1.5 in size.~ White color and has some powder residue.

Recommendation:It is great for building roads, driveways, walkways, or parking lots. It can also be used for landscape decoration.

~ 1/4 to 1, mostly 5/8 in size.~ Multi color.

Recommendation: Main use- Decorative applications in concrete sidewalks and flowerbeds.

~ Drain water very well, Goldish-Brown color ( Copper).

~ High in trace minerals and environmental safe.

Recommendation: May be used for hiking paths, walkways, tracks, driveways and base for pavers or flagstone patios.

~ A crushed basalt gravel available in 5/8 size with a dark grey look when dry, and very black look when wet.

Recommendation:Can be used for walkways, fill in the gaps in between patio stones, and for water features.

~ It is a recycled aggregate~Dust to 1.5in size

~*size may vary from the picture*

Recommendation:A good alternative to gravel as a drainage material in wet areas. it may be also used as a base for driveways and parking lots.

Continued here:
Sand & Gravel Landscape Materials - The Yard Depot

Gorilla Gutters Inc has built a strong reputation for maintaining the highest professional standards in the gutter installation and gutter cleaning industry, including outstanding workmanship and customer service. Our team of experienced professionals is efficient, meticulous, dedicated and always strives to keep the costs of our gutter services in complete alignment with your budget needs. Gutter Repair.

Our highest priorities are always customer satisfaction, safety, and maintaining the security and overall integrity of your property. Although this business requires us to work in your yard and around your home, we take extra special care to maintain all of your propertys distinct elements and landscapemaking sure to leave things exactly the way we found them.

At Gorilla Gutters Inc, we go the extra mile to ensure our customers are satisfied. We want you to call again and to tell a friend or two about us too! We understand our long-term viability depends on your overall satisfaction. At Gorilla Gutters Inc, our top priority is your satisfaction. We are here for you!

Call Gorilla Gutters Inc. today for your FREE estimate: 510-524-1111 or 925.255.5555 or fillout our short contact form here

You may think we have our heads in the gutter, and we do! Check out our new Gutter BLOG

Go here to see the original:
Gorilla Gutters - Gutter Cleaning Oakland Berkeley ...

Committed to ridding your home or office of unwanted pests, insects and termites.

Amongst leading pest control companies, we cover all general pest & insect control services including Ants, Rats, Cockroaches, Silverfish, Termites,Spiders, Fleas, Wasps, & Bed Bugs.

Due to many contributing factors, there has been a rise in the demand for pest control in Melbourne, Victoria. Things like unpredictable weather have led to more and more pests finding their way into homes and increasing the need for residential pest control in Melbourne. In particular, the demand for pest control in Melbourne Eastern Suburbs has skyrocketed.

Thats where we come in. At Everyday Pest Control, we pride ourselves on offering the best pest control in Melbourne, along with a highly responsive service. Whether you are experiencing an influx of ants, or an invasion of rodents, we have a range of techniques in natural pest control in Melbourne to render your property pest free.

If you are simply looking for a quote or some friendly expert advice regarding pest removal in Melbourne, feel free to contact us today. We provide only excellency in the field and always aim to keep our prices down in order to offer cheap pest control in Melbourne.

See the original post here:
Commercial & Domestic Pest Control Company Melbourne ...

Commercial

From start to finish, our team works together to make sure you get the best value for your budget in your commercial project. Our estimators and project managers work together to ensure your project runs smoothly from start to finish.

The industry experts at MIINC make going from design to execution simple and straightforward. Our project managers work with you every step of the way to make sure the job gets done right, on time and on budget.

Our full-service maintenance package will ensure your system stays up and running for many years to come. By keeping your system maintained properly, we help you prevent costly fixes or replacements in the future.

To provide the highest quality systems and services while honoring God, which result in the success of MIINC L.P. and our employees.

To be recognized as the leading provider of mechanical system solutions in Texas and surrounding states.

Read the rest here:
HVAC, Commercial Plumbing & Mechanical System ... - MIINC LP

A highly technical task, tree removal requires trained and qualified professionals. Tree removal addresses the health and aesthetics of your landscape as well as the safety and liability of host and adjacent properties. Strategic tree removal can enable competing species to develop and mature. In certain instances, it may be necessary to remove a tree that is alive if it is interfering with the health and vigor of other trees, or threatens buildings, driveways, or utility wires.

A SavATree arborist may determine that there is a reasonable alternative to tree removal which will allow you to keep your beloved tree. Proactive tree care and maintenance is the best way to ensure the vigor and longevity of your trees and shrubs. Cabling and bracing can provide supplemental support to your tree if it is determined to be structurally weak. This supplemental support will help to prevent injuries to your trees, such as crotch and branch failure, and provide some protection against storm damage. This practice can extend the life of feature trees.

Tree removal in urban and suburban landscapes can present a challenge. Neighborhood trees are often surrounded by other valuable plantings and structures. Urban trees can pose hazards to the public. Tree removals, especially for large trees, require careful dismantling by highly trained personnel utilizing state-of-the-art machinery to ensure the protection of your home and property. The use of specialized equipment during tree removals is determined by the conditions on your landscape, branch architecture, and the soundness of your tree. A standard tree removal includes taking down a tree, chipping all brush, cutting all wood into 20 logs, and cutting the stumps as flush as possible to the ground. Wood may be stacked at or near the base of the tree or removed from the site depending your specifications. We also can provide stump removal and disposal services.

Call today for a complimentary tree removal consultation with SavATrees fully trained and certified arborists. Click here to sign up for a complimentary consultation.

Go here to see the original:
Tree Removal Services Performed by Experts | SavATree