Home Builder Developer - Interior Renovation and Design

How to Install Hardwood Floor Panels With the Nail Down Method by Niv Orlian There are many ways to install a wood floor. The nail down technique of laying hardwood floors has become very popular. For those learning how to install hardwood floor, theres no simpler or straightforward technique than the nail down technique. Unlike other methods which basically require you to be an amateur carpenter or even a professional carpenter, the nail down method on how to install hardwood flooring can be accomplished by anyone who can swing a hammer. Well, thats not all it takes. You also have to be persistent, patient, and willing to try new things if you want to learn how to install hardwood floor. Also, you need to be willing to read the safety instructions that come with the tools youll be using. Tools Youll Need as Your Learn How to Install Hardwood Floor Panels Broom and Dust Pan - You need to clean up constantly as you learn how to install hardwood floor to make sure no dirt, sawdust, or other debris get caught in between the grooves or under the boards. Carpenters Crayon - Use this to create guidelines on your sub floor. Youll also need it to draw lines where youll cut your hardwood panels. Claw Hammer - Any areas near obstacles or walls where you cant get enough space to swing a rubber mallet will have to be reached with your claw hammer. Cutter Knife - Use this often for unforeseen activities involved as you learn how to install a wood floor. But the main purpose of this device will be to cut out any excess wood when adjustments of only a millimeter or two need to be made. Electric Drill and 3/32 Drill Bit - Use this to drill your pilot holes, which should be slightly smaller in length and circumference than your nails. This will prevent your flooring panels from cracking when you put the nails in them. Hardwood Flooring Nails (2) - These nails are important because they will be what hold your floor in place. Nailer - This can either be a hammer or pneumatic nail gun. The pneumatic nail gun is obviously faster and easier, but you have to get it calibrated just right so that the nails dont go too far down into the wood and destroy your hardwood panels. Rubber Mallet - This is your chance to pound your frustrations out as you learn how to install hardwood floor. Actually, you should pound them out gently to bring the surfaces of the two panels together perfectly. You dont want to get them too far apart or your floor will have crevices. But if you pound them too hard together, you can damage them or push them so far together as to bow them. Circular Saw - At the end of each row of boards as you go into the corner, you will need to cut your floor panels to fit. Any fixtures in the room will also have to be cut around. Preparing to Install Hardwood Floor Panels Although the nail down method of installing hardwood floor panels is pretty simple, it should still be done carefully as the hardwood floor has to endure for many years in whatever form you complete it. All of the furniture and obstacles that can be removed from the room should be removed while you install your hardwood floor panels. This is true even if it requires manual dismantling and reassembly. For those fixtures build into the floor of the room, youll just have to panel around them. Its not the easiest way to go, but you have to do what you have to do to get your hardwood floor installed. If you have door sills, an old hardwood floor, baseboards, or carpet, remove them before you begin as well. If the surface beneath where you will be flooring is cement or any other lumpy material, use a felt floor liner to cover this surface. Then install a plywood sub-floor over it. Once laid, you should be ready to begin installing the hardwood floor. Steps on How to Install Hardwood Floor Panels 1. Put your first floor panel in the corner of the room in which you have decided to start your flooring. The grooves should be toward the wall and the tongues should be toward the room. 2. Start adding panels to make a row. The last panel shouldnt quite fit right, so youll have to use that carpenters crayon to mark where to cut it. Use your circular saw to cut it. Be very careful not to cut it too small. The fitting needs to be just about perfect. 3. Use your drill to make your little pilot holes. Put the nails in to fasten your floor down. Though it will take longer, youll be thankful when youre done if you used pilot holes when youre learning how to install hardwood floor. 4. Grab the other half of the panel you cut off the row you just completed and use it as the starting point for the next row. This will seem strange at first, but when the floor is completed, the offset of the boards will look really nice. Additionally, if all of your boards matched up, the floor wont have interlocked strength. 5. Continue on doing this as you go through the remaining rows. Use the rubber mallet as necessary to make the boards and rows nice and snug. When the rubber mallet wont fit, use the claw hammer to pull the boards tight. The last things you need are some giant crevices between your boards when youve finished your new hardwood floor. 6. The last panel is the hardest one to get put in place, but your floor will look really awful if you hurry at this step. You need to patiently measure, cut, and make your last panel fit. 7. Clean the floor you just laid. Cleaning Up After You Install Hardwood Floor Panels In the process of how to install hardwood floors, cleaning up is important and overlooked enough to warrant its own follow-up section. But unlike other nail down method guides on how to install hardwood floor panels, we want to make sure you understand this step. Cleaning up is important because there are little wood chips and saw dust everywhere after the typical hardwood floor installation. Use your broom and dust pan to pick up any debris on the floor. These particles, if walked on and rubbed on by furniture, can make your brand new floor look like a scratched up old floor pretty quickly. Unless you went beyond the instructions on how to install wood floors and used glue on your hardwood panels, theres no need to get your floor wet before it has had a chance to settle. This is because you dont want it to swell before youve moved the furniture back in and given it a couple days to get itself in its final arrangement. Special Tips Add-On on How to Install Hardwood Floor Panels Dont get too aggressive when putting your hardwood flooring in place. Its very easy to ruin the surface of floor panels when theyre floating freely and youre placing them and pounding on them. Be especially careful when fixing a row that looks a little bit off. If your rubber mallet is sturdy enough, itll be the best thing to put nails in because it wont do as much damage to the surface of your floor panels. Your nailed down floor probably isnt going to be quite as nice as the one installed by a professional. On the other hand, its going to look pretty nice on its own. It will probably be about the nicest looking job an inexperienced hardwood floor installer can do. And if you change your mind about the floor, its one of the easiest hardwood floor installation methods to undo. But besides being easy to install and uninstall, nailed down hardwood floor has some usage advantages over other types. The main advantage to keep in mind is that a glued down floor is rigid; once a floor panel is dried in place, its there for good whether its snug to the next panel over or not. The loose floor isnt attached to anything and can be creaky, bubbly, and move around. So enjoy your new well-fixed hardwood floor. Ezine is the source of this article. Click here if you are interested in learning how to install a floating hardwood floor For more background information about hardwood floors here is a link to an interesting research article from the University of Wisconsin

Take a look at this store to see if we might have some tools you need. Diamond-Stuff Amazon Tool Store

Read the rest here:
Install Wood Floor

Floored by ORCON: Tack Strip in Carpet Installation
Floored by ORCON: Tack Strip in Carpet Installation talks about the different considerations in choosing tack strip and installing it. Anchoring the carpet...

By: Halex Corporation

Originally posted here:
Floored by ORCON: Tack Strip in Carpet Installation - Video

Bob Hope Airports Terminal A will be getting new carpet, but the installation work will be scheduled for nighttime hours to avoid inconveniencing passengers.

The Burbank-Glendale-Pasadena Airport Authority last month approved a contract for the first phase of the work, which is estimated to cost around $220,000 and will begin in roughly two months. The last time the carpet was replaced in the terminal building was about 15 years ago in 2000, according to a staff report.

This week, airport staff also updated the commission on the project in response to Pasadena Commissioner Terry Torneks request for more information on the per-square-yard cost of the work.

I install a lot of carpet, Tornek said last month. Thats a big number.

The first of two phases calls for replacement of the carpet in the terminals main entrance, ticket counter area and the hallway leading to the security screening point. It is expected to be completed by the close of the airports fiscal year on June 30.

Airport staff had solicited bids for the first phase and received two responses. Reliable Floor Covering Inc. of Westlake Village was the lowest bidder and was awarded the contract.

Dan Feger, the airport's executive director, said last month that recarpeting the airport has historically run around $40 per square yard installed, for a variety of reasons, including the much more difficult requirements of the work.

This week, airport staff provided a more comprehensive update on the costs in response to Torneks request, which showed costs were significantly higher than those rates in the past, based on the contract cost divided by the surface area.

Bob Anderson, the airports director of engineering and planning, said the lowest bid for project in 2011 to replace all of the carpet in Terminal A was $630,000 around $72 per square yard which was deemed too expensive.

In light of economic conditions and a decrease in passenger traffic at the time, the airport instead replaced only the carpet in the most heavily trafficked section of the airport, the center hallway in the east concourse, which cost $90.74 per square yard, or roughly $240,000.

Continued here:
New carpeting slated for airport terminal

I've never been to Portland, but I've seen the airport's carpet a million times. If you asked me to draw a picture of the delightfully geometric 80s design, I could probably do it with my eyes closed. How, you wonder? Hipsters. That's how.

Hipsters just love that blue-green carpet at the Portland International Airport (PDX). The 25-year-old design has been spun off into so many clothing lines and social media accounts, you could call the PDX carpet a hipster icon. Not for long, though. Last month, airport officials began ripping up the 14 acres of stained, fraying fabric that cover the terminal floors and replacing it with a curvier new design. And the hipsters are pissed.

Over two decades before Portlandia introduced the world to the inside jokes of the Pacific Northwest paradise, Portland was a sleepy city. But it was also gearing up for a renaissance, a reinvention that would turn the old trading post in Mount Hood's shadow into a city fit for the 21st-century. To make this possible, the airport would need to get bigger.

In the 1980s, the Portland International Airport underwent a series of renovations and expansions that would eventually yield two new new concourses, moving sidewalks, and a small shopping mall. All of this new floorspace would need new carpet, so airport officials hired SRG Partnership for the job. The local architecture and design firm quietly decided to draw inspiration from the airports X-shaped runways as seen from the control tower. The dark blue, purple, and red pattern on a teal-colored background reflected the popular design trends of the time, though it hardly seemed like would become so timeless.

Workers laid 28,000 square feet of the iconic carpet throughout PDX's terminals in 1987. Jon Schleuning, the founding partner of SRG Partnership, had designed the glitchy look with the help of his colleague Laura Hill. (Hill recently wrote about the design process.) The team got lots of compliments on the design at the time of the installation, but they never expected it to develop a cult following.

But the airport expansion foreshadowed a much more ambitious plan for Portland. A year after the new carpet was glued to the floors of PDX, the city's Bureau of Planning adopted an ambitious initiative called the Central City Plan. The near 200-page plan aimed to "guide the Central City into the 21st-century" by boosting the economy and spurring smart growth. That meant preserving the Mount Hood corridor, expanding retail and office space downtown, extending the Light Rail system, and building a huge new convention center. In effect, Portland was preparing for a huge influx of visitorsand hopefully residents, too.

For a complicated set of reasons, Portland's wish came true. With the 9os came the dot com boom and a massive explosion of computer-related industries throughout the city. This meant that there were lots of jobs for young developers and, more importantly, young graphic designers. It didn't hurt that Portland's rent was cheap or that the city was surrounded by natural splendor. All things considered, Portland was one of the hottest cities of the 90s in terms of growth.

The rest is here:
How the Portland Airport Carpet Became a Hipster Icon

Basement Finishing Burlington - Remodeling Discount - Lux Renovations
Looking for Basement Finishing Contractors in Burlington MA? Mention this Video and Receive $2500 Off Your Basement Remodeling Project Today! You Can Also Visit Us At - http://www.ocboston.com ...

By: Lux Renovations, LLC

See the article here:
Basement Finishing Burlington - Remodeling Discount - Lux Renovations - Video

Basement Finishing Boston MA - Remodeling Discount - Lux Renovations of Massachusetts
Looking for Basement Finishing Contractors in Boston MA? Mention this Video and Receive $2500 Off Your Basement Remodeling Project Today! You Can Also Visit Us At ...

By: Lux Renovations, LLC

View original post here:
Basement Finishing Boston MA - Remodeling Discount - Lux Renovations of Massachusetts - Video

Basement Finishing NH - Remodeling Discount - Lux Renovations of New Hampshire
Looking for Basement Finishing Contractors in NH? Mention this Video and Receive $2500 Off Your Basement Remodeling Project Today! You Can Also Visit Us At ...

By: Lux Renovations, LLC

Original post:
Basement Finishing NH - Remodeling Discount - Lux Renovations of New Hampshire - Video

WASHINGTON TWP. Long Valley resident Joseph Fernandez knows how to treat his customers and hes gotten a special award for his efforts.

Fernandez, owner of JMF Construction, LLC, has won the 2015 Customer Service award from Houzz, a website dedicated to remodeling and interior design professionals.

Fernandez has been using his skills on his own Jacki Drive home since 2006. He made plans for the house before he even closed on the deal. Plans included blowing out walls to dramatically redraft the floor plan, as well as building all the cabinetry and most of the furniture.

Not a lot of contractors work on their own house, though I dont know why, Fernandez said. I know some guys who have, and obviously, I do. If youve got the talent, why not enjoy it yourself?

Fernandez, 55, followed a less traditional path to starting his own business in 1986. He worked in the stagecraft end of theater in high school and while attending Emerson College in Massachusetts, where he later designed sets for his alma mater. He worked on productions as far as Tulsa, Okla. to Lake George for opera troupes and Broadway productions including helping with sets for Little Shop of Horrors and productions by the Julliard School in New York City. Eventually, he began working on construction, and said he found his passion for woodworking in custom furniture and cabinetry, mainstays to his remodeling business.

Ive done the Little Shop of Horrors in Manhattan, worked for Julliard, and run a lot of that stuff on my own, Fernandez said. I went into construction and moved up from custom cabinetry to overseeing a five story brownstone renovation project in the city.

Fernandez said he continued in construction when his employer went out of business. An architect he knew referred Fernandez remodel a home for a fellow theater worker.

From then on, I was in business, Fernandez said. I bought some tools and worked out of my fathers basement at first, then moved on to my own shop in Hillsboro, and eventually moved on to just running shop out of my home.

In almost a decade at Long Valley, his home has been a work in progress, though it has always served well as a display of his work that he cant help but tweak.

I moved here because I do a lot of work in Chester and Mendham, but I also stretch all the way from Peapack to Summit, as far as Jersey City. Theres a lot to do with upscale clients in Morris County and Essex, Fernandez said.

Go here to see the original:
Contractors model home in Long Valley shows his talents

SEASON-Led indoor lighting manufacturer
Providing laser printing LOGO Service to our customers --SEASON Optoelectronics Technology Limited, established in 2011, is a professional LED lighting enter...

By: Vincent Jiang

Read the original post:
SEASON-Led indoor lighting manufacturer - Video

Indoor Lighting for GCU (year 3)
This project focused on lighting, so some of the models were give to us. I modeled the sofa, lights and speakers Lighting done in 3ds Max, most of the modeli...

By: holeysh

Read more:
Indoor Lighting for GCU (year 3) - Video