Recommended Guidelines/Priorities for Sidewalks and WalkwaysIntroduction

According to the American Association of State Highway and Transportation Officials (AASHTO) A Policy on Geometric Design of Highways and Streets (also known as the Green Book): Providing safe places for people to walk is an essential responsibility of all government entities involved in constructing or regulating the construction of public rights-of-way.

It is a basic principle that there be well-designed, safe places for people to walk along all public rights-of-way. How this will be accomplished will depend upon the type of road, whether it is new construction or a retrofitted area, and funding availability.

On February 24, 1999, Federal Highway Administration (FHWA) Administrator Kenneth R. Wykle, in a memorandum to FHWA field offices, stated, We expect every transportation agency to make accommodations for bicycling and walking a routine part of their planning, design, construction, operations, and maintenance activities. Again, in February 28, 2000, Administrator Wykle sent a memorandum to the field offices in transmitting the new Design Guidance Language called for in the Transportation Equity Act for the 21st Century (TEA-21). The guidance, entitled Accommodating Bicycle and Pedestrian Travel: A Recommended ApproachA U.S. DOT Policy Statement on Integrating Bicycling and Walking Into Transportation Infrastructure, states that bicycling and walking facilities will be incorporated into all transportation projects unless exceptional circumstances exist. The exceptional circumstances are spelled out, and he asked the division offices to work with State departments of transportation (DOTs) in the implementation of the guidance.

Government agencies at the State, regional, and local level are developing regulations for funding, installing, and retrofitting sidewalks. Because there is a great need to improve sidewalk facilities, it is important for these transportation agencies to direct funding to sidewalk improvement and installation projects that will be most beneficial to the safety and mobility of all citizens.

This document is intended to provide agencies at the State, regional, and local levels with tools they can use to develop guidelines for creating places for people to walk.

This document is limited to creating guidelines for sidewalks, which addresses only one major pedestrian need; other needs that merit further consideration include the ability to cross a street and intersection design.

Many communities may wish to revisit their roadway planning and rehabilitation criteria. Policies, standard plans, subdivision regulations, and right-of-way requirements should be considered to make sure that sidewalks are included in new construction and rehabilitation projects.

Typically, communities should focus on: (1) improving conditions for people who are currently walking (including improved accessibility to sidewalk facilities for pedestrians with disabilities), (2) increasing levels of walking, and (3) reducing the number of crashes involving pedestrians. Setting targets will help in the development of criteria for installing and retrofitting sidewalks.

There are several ways in which pedestrians can be accommodated in the public right-of-way:

Places for people to walk should be provided in all new construction. Retrofitting will require priorities to be set, and these guidelines are intended to help identify where the need is greatest for adding sidewalks and other facilities.

All new construction must include places for people to walk, on bothsides of a street or roadway. New construction inurban and suburban areas should provide sidewalks.Recommended guidelines for new sidewalk and walkwayinstallation are given in Table 1 below.

In developing areas and rural areas, it may be acceptablealthough less desirableto start with shoulders and unpaved paths and then phase in sidewalks as development accelerates. Criteria for installing sidewalks along with new development should be implemented with the following in mind:

There is a desire in some residential developments to retain a rural atmosphere. Very often this occurs in places that are not truly rural, but rather suburban or exurban (they may have been rural before being developed). Frequently, it is in such places that pedestrian crashes occur that are directly attributable to pedestrians not having places to walk. To address both the goal of having safe places to walk and that of the community to retain a certain atmosphere, path systems can be developed that do not look like traditional sidewalks, but do meet walking needs. Even in rural areas, people do want to walk and such facilities should be provided.

Developers in outlying areas may argue that the land use will never fully develop into a pedestrian area. Given that people walk despite not having facilitiesfor exercise, going to friends houses, accessing transit, etc.it is neither rational nor acceptable to build places that do not have places for people to walk. Residential developments that were added in suburban areas, until recently, typically had sidewalks and functioned very well.

Sidewalks may not be needed on short residential cul-de-sacs (61 m [200 ft] or less), if there is a system of trails behind the houses and driveway aprons are properly constructed for pedestrians with disabilities. However, it is not a good practice to have an entire neighborhood without sidewalks.

Sidewalks should be continuous; interruptions may require pedestriansto cross a busy arterial street midblock or at an unsignalized locationto continue walking. Sidewalks should also be fully accessible to sidestreets and adjacent sidewalks and buildings.

1 acre=0.4 hectares (ha)

Many of the streets built in recent decades do not have sidewalks, and these streets need to be retrofitted. In other cases, existing sidewalks need to be replaced. Establishing priorities for installing sidewalks involves three steps: (1) develop a prioritized list of criteria, (2) develop a methodology for using the criteria to evaluate potential sites, and (3) create a prioritized list of sites for sidewalk improvements.

The following are suggested criteria for establishing priorities. Select three or more of them when developing your own set of criteria. The key is to select criteria that produce the outcomes desired for your community:

Seattle recently completed an inventory of all sidewalksin the city using a three-step process:

The totaleffort took the equivalent of one full-time person working for 6 months in a city of 530,000 population,218.3 km2 (84.3 mi2) of land use and 2,659 roadway kilometers (1,652 roadway miles) [1,934 residential street kilometers (1,202 residential street miles) and 724 arterial kilometers (450 arterial miles)]. Once the inventory was completed, the information was combined on a map with three other types of information:

Once the map was printed,it was very easy to see where the three colorsoverlapped, two colors overlapped, etc. The final step was to have the computer calculate the sidewalk deficiencies in the overlapping areas. They found, for example, that there were less than 3 km (2 mi) of arterialstreets that were within school walking zones,a pedestrian generator area, and a neighborhood commercial area that did not have sidewalks on either side of the street.

There were nearly 4.8 km (3 mi) of arterial streets that were within school walking areas, but outside of neighborhood commercial areas and pedestrian generators that did not have sidewalks on either side of the street. This was compared to a citywidedeficiency of more than 32 km (20 mi) of arterialstreets that lacked sidewalks on both sides of the street.

By developing these and other numbers, the pedestrian program was able to put together packages of information that demonstrated what could be accomplishedwith additional funding. What everyone thoughtto be an unsolvable multi-million-dollar problemwas reduced to a series of smaller, fundableprojects that decisionmakers could endorse. Theresult was increased funding and a new optimismthat meaningful progress could be made on solving Seattles sidewalkdeficiencies.

The two recommended methodologies for selecting locations for improvements are: (1) the overlapping priorities method, and (2) the points method. Establishing priorities should consume only a small percentage of a program budgetthe level of effort put into prioritization should be proportionate to the size of the capital budget.

There is no single right way to select which criteria to use when developing priorities. The criteria and methodology should balance safety measures, such as vehicle speeds and pedestrian crash data; pedestrian usage measures, such as proximity to schools or commercial areas; continuity between origins and destinations; and accessibility for pedestrians with disabilities.

1. Overlapping Priorities Method The easiest and cheapest way to identify overlapping priorities is through graphical representation; the intent is to identify locations that meet multiple criteria. This methodology is especially useful in cases where there is not a lot of staff time and funding for detailed analysis. It can be accomplished using a GIS system or it can be done by hand.

The best way to describe this methodology is by example. Assume that priorities are going to be developed based on transit routes, proximity to schools, people with disabilities, and neighborhood commercial areas. Start with a map of your jurisdiction. Using a color pen, identify those arterials that have high transit use; draw a half-mile circle around every elementary school and around locations that attract people with disabilities; and color in the neighborhood commercial areas. This visual approach will make areas of overlapping priorities become immediately clear. The streets without sidewalks within the overlapping areas are the highest priority for retrofitting sidewalks.

2. Points Method A weighted points system can be used where staff time and funding are available for more detailed analysis, or if there is a large amount of capital available for sidewalk construction. If there are a lot of competing projects, a more sophisticated point system can be used to explain to the public why certain projects were funded and others were not.

A point system can be developed in many ways; the system should be simple and produce desired outcomes. Any and all of the criteria listed above can be assigned a range of numbers and then be used to analyze the need for improvement at given locations. For example, a corridor could be assigned points based on the number of walking along roadway crashes over a 5-year period, the number of buses that travel the corridor during peak times, and the proximity to elementary schools. This method is time-consuming because it will be necessary to analyze multiple locations with sidewalk needs to create a list of priority projects.

3. Prioritized List Both the overlapping priorities and the points methods will produce an initial list of prioritized projects. The next step is to refine the list so that it works, using common sense. One important consideration is that when roadways are resurfaced, rehabilitated, or replaced, curb ramps must be added if there are pedestrian walkways. In addition, the U.S. Department of Justice considers bus stops to be pedestrian walkways requiring access for people with disabilities, so areas near transit should be given priority accordingly. Improving pedestrian crossings, particularly on arterial streets, may also be an important part of some projects. Other important questions include: Are priority locations ones that might be expected? Are there many surprises? Are priority locations in line with community priorities and expectations? Are some priorities at locations with very low pedestrian use? If the answer to these questions is "yes," then the criteria or the methodology should be evaluated and possibly revised to create outcomes that better reflect expectations and desires. The methodologies should be used to prioritize known needs, not to create a new set of priorities that dont make sense.

The final step is to create packages of fundable projects. The prioritization process should result in reasonable packages that decision-makers can embrace and support. For example, it may be possible to install sidewalks on both sides of every arterial within a half-mile of every elementary school for $5 million over a period of 5 years. Or, it may be possible to replace sidewalks in neighborhood commercial areas for $2 million over a period of 3 years. The objective is to take what may appear to be an unsolvable problem (endless need for more funds) and to package it in such a way that it begins to address some of the most critical pedestrian needs in a community.

Continuous sidewalks should be placed along both sides of all fully improved arterial, collector, and local streets in urban and suburban areas. Sidewalks should connect to side streets and adjacent buildings. Accessible crossings should be provided across median islands, frontage road medians, and other raised islands.

A safe walking area must be provided outside the motor vehicle traffic travelway. Sidewalks along rural roads should be well separated from the travelway. Isolated residential areas should have a pedestrian connection to the rest of the rural community for school access, shopping, and recreational trips.

An off-road pathalso known as a side pathis a type of walkway used in some rural settings. This path may be paved or unpaved, and is separated from the roadway by a grass or landscaped strip without curbing. This maintains a rural look, but is safer and more comfortable than a shoulder.

A paved or unpaved shoulder should be provided as a minimum along the road. Paved shoulders are preferred to provide an all-weather walking surface, since they also serve bicyclists and improve the overall safety of the road. A 1.5-m- (5-ft-) wide shoulder is acceptable for pedestrians along low-volume rural highways. Greater width, up to 2.4 to 3.0 m (8 to 10 ft), is desirable along high-speed highways, particularly with a large number of trucks. An edgeline should be marked to separate the shoulder from the travelway.

The width of a sidewalk depends primarily on the number of pedestrians who are expected to use the sidewalk at a given time high-use sidewalks should be wider than low-use sidewalks. "Street furniture" and sidewalk cafes require extra width, too. A sidewalk width of 1.5 m (5 ft) is needed for two adult pedestrians to comfortably walk side-by-side, and all sidewalks should be constructed to be at least this width. The minimum sidewalk widths for cities large and small are:

*2.4-m (8-ft) minimum in commercial areas with a planter strip, 3.7-m (12-ft) minimum in commercial areas with no planter strip.

These widths represent a clear or unobstructed width. Point obstructions may be acceptable as long as there is at least 914 mm (36 in) for wheelchair maneuvering (no less than 1,219 mm (48 in) wide as a whole); however, every attempt should be made to locate streetlights, utility poles, signposts, fire hydrants, mail boxes, parking meters, bus benches, and other street furniture out of the sidewalk. When that is not possible, sidewalk furnishings and other obstructions should be located consistently so that there is a clear travel zone for pedestrians with vision impairments and a wider sidewalk should be provided to accommodate this line of obstructions.

Similarly, when sidewalks abut storefronts, the sidewalk should be built 0.6 m (2 ft) wider to accommodate window-shoppers and to avoid conflicts with doors opening and pedestrians entering or leaving the buildings.

Many 1.2-m (4-ft) sidewalks were built in the past. This width does not provide adequate clearance room or mobility for pedestrians passing in opposite directions. All new and retrofitted sidewalks should be 1.5 m (5 ft) feet or wider.

Buffers between pedestrians and motor vehicle traffic are important to provide greater levels of comfort, security, and safety to pedestrians. Landscaped buffers provide a space for poles, signs, and other obstructions; they serve as a snow storage area; and they protect pedestrians from splash. The ideal width of a planting strip is 1.8 m (6 ft). Minimum allowable landscape buffer widths are:

With a landscaped buffer between the sidewalk and the street, care must be taken to ensure that the bus stops are fully accessible to wheelchair users and have connections to the sidewalk. Irrigation may be needed in areas of low precipitation.

Buffers also provide the added space to make curb ramps and landings accessible. When the ramps and landings are designed properly, they are also better utilized by those pushing strollers or pulling carts and luggage.

If a planting strip is not provided between the sidewalk and roadway, then the sidewalk width should be a minimum of 1.8 m (6 ft).

Where landscaped sidewalk buffers cannot be provided due to constraints, on-street parking, a shoulder, or a bike lane can serve to buffer pedestrians from motor vehicle traffic lanes.

Concrete is the preferred sidewalk surface, providing the longest service life and requiring the least amount of maintenance. Asphalt is an acceptable walkway surface in rural areas and in park settings, and crushed granite may also be an acceptable all-weather material in parks or rural areas, but they generally require higher levels of maintenance and are less desirable for wheelchair users.

Sidewalks may be constructed with bricks and pavers if they are constructedto avoid settling; bricks should be easy to reset or replace if they causea tripping hazard. Also, bricks and/or pavers can cause vibrations thatare painful for pedestrians who use mobility aids and, therefore, it maybe appropriate to use bricks or pavers only for sidewalk borders in certainsituations. There are stamping molds that create the visual appearanceof bricks and pavers; these have the advantages of traditional concretewithout some of the maintenance issues and roughness associated with bricksand pavers. There are commercially available products that produce a varietyof aesthetically pleasing surfaces that are almost impossible to distinguishfrom real bricks and pavers. However, stamped materials can also havemaintenance issues, since, for example, the sidewalk may never look thesame again after repairs are made.

It is also possible to enhance sidewalks aesthetics while still providing a smooth walking surface by combining a concrete main walking area with brick edging where street furniture (lights, trees, poles, etc.) can be placed. For example, in a CBD, a 4.6-m (15-ft) total sidewalk width might include a 2.4-m (8-ft) clear concrete sidewalk with a 2.1-m (7-ft) edge.

Sidewalks should be built to accommodate all pedestrians and should be as flat as practical. Sidewalks should be held to a running grade of 5 percent or less, if possible. However, sidewalks that follow the grade of a street in hilly terrain cannot meet this requirement, for obvious reasons, and may follow the grade of the street. The maximum grade for a curb ramp is 1:12 (8.3 percent).

The maximum sidewalk cross-slope is 1:50 (2 percent) to minimize travel effort for wheelchair users and still provide drainage. At least 0.9 m (3 ft) of flat sidewalk area is required at the top of a sloped driveway to accommodate wheelchair use. In some cases, it may be necessary to bend the sidewalk around the back of the driveway to achieve a level surface of 0.9 m (3 ft).

Curb ramps must be provided at all intersection crossings (marked or unmarked) and midblock crosswalks for wheelchair access. These ramps also accommodate strollers, carts, the elderly, and pedestrians with mobility limitations. Curb ramps should be as flat as possible, but must have a slope no greater than 1:12 (8.3 percent). Abrupt changes in elevation at the top or bottom should be avoided. The minimum curb ramp width is 914 mm (36 in); however, 1,219 mm (48 in) is the desirable minimum. If a curb ramp is located where pedestrians must walk across the ramp, the ramp must have flared sides of no more than 1:10 (10 percent) slope. These flares are not needed where ramps are placed in a landscaped area. Curb ramps also require a minimum of 914 mm (36 in) of level and clear passage (1,219 mm (48 in) or more are desirable) at the top.

Two separate curb ramps, one for each crosswalk, should be provided at each corner of an intersection. Diagonal curb ramps provide no directional guidance to vision-impaired pedestrians, and force wheelchair users to maneuver in the crosswalk. Raised islands in a crossing must have at least a 1,219-mm (48-in) cut-through that is level with the street; this is generally preferable to curb ramps, which force wheelchair users to go up and down.

The distance to the bottom of signs placed in or right next to a sidewalk should be at least 2 m (7 ft) above the sidewalk surface to avoid injury to pedestrians. Bushes, trees, and other landscaping should be maintained to prevent encroachment into the sidewalk. Jurisdictions should adopt ordinances requiring local property owners to trim the landscaping they place along their frontage to maintain clear and unobstructed sidewalks. The jurisdictions should provide an inspection procedure or a system of responding to sidewalk encroachment and maintenance complaints.

Guy wires and utility tie-downs should not be located in or across sidewalksat heights below 2 m (7 ft). When placed adjacent to sidewalks or pedestrianwalkways, the guy wires should be covered with a bright yellow (or otherhigh-visibility) plastic guard to make the wire more visible to pedestrians.Guy wires of any color will not be visible to blind pedestrians and mustnot be located within the pedestrian route. Other obstacles include signalcontroller boxes, awnings, temporary signs, newspaper racks, fire hydrants,and similar items.

The easiest way to visualize accessibility requirements (grade, cross-slope, and clear width) is with the concept of a continuous passage. Sidewalks must provide a continuous route at a 2 percent maximum cross-slope at a minimum width of 0.9 m (3 ft). This does not mean that 0.9 m (3 ft) is an acceptable sidewalk width, just that at no point shall the level area be less than 0.9 m (3 ft) wide; this applies mainly at obstructions, driveways, and curb ramps.

Municipalities that do not remove snow on sidewalks should have an ordinance requiring property owners to clear the snow and keep the sidewalks accessible to pedestrians. When the latter is the case, municipalities should educate property owners as to why this is important and have enforcement efforts in place to ensure compliance.

It is generally preferable to place bus shelters between the sidewalk and the street, or between the sidewalk and adjacent property, so that waiting passengers do not obstruct the flow of pedestrians along the sidewalk. Benches and other street furniture should be placed outside the walking paths to maintain the accessibility of the walkway and to provide good pedestrian service. In addition, curb ramps should be provided at bus stops because it is not always possible for the bus to pull close enough to the curb to deploy a lift.

Good street lighting improves the visibility, comfort, and security of pedestrians. In urban areas, it is important to light at least the intersections and other pedestrian crossing areas. Lighting is also recommended in areas where there is a high concentration of nighttime pedestrian activity, such as churches, schools, and community centers. Where continuous lighting is provided along wide arterial streets, it is desirable to place the lights along both sides of the street. Continuous streetlights should be spaced to provide a relatively uniform level of light. In shopping districts or in downtown areas with high concentrations of pedestrians, it is desirable to provide pedestrian-level lighting in addition to the street lighting to improve the comfort and security of pedestrians. The preferred pedestrian-level lights are mercury vapor or incandescent. Low-pressure sodium lights may be more energy-efficient; however, they are undesirable because they create considerable color distortion. Pedestrian-level lighting may also be installed in selected areas of pedestrian activity to create a sense of intimacy and place.

Sidewalks should be built within the public right-of-way or in a sidewalk easement along the right-of-way. This will provide access to the sidewalk for maintenance activities and will prevent the adjacent property owners from obstructing or removing the sidewalk in the future.

Care must be taken to avoid planting trees or large bushes in the landscape buffer area that will obscure the visibility between a pedestrian attempting to cross or enter a street and an approaching motorist. Trees with large canopies planted between the sidewalk and street should be generally trimmed up to at least 2.4 m (8 ft) high and bushes should be kept to about 762 to 914 mm (30 to 36 in) in height. Trees with large caliper trunks may not be appropriate near intersections and in other situations where they may block visual sight triangles.

Meandering sidewalks are sometimes used where a wide right-of-way is available and there is a desire to provide a high level of landscaping, such as in a park or along a waterway or other natural feature. It is often believed that meandering sidewalks create a more pleasant walking environment. The reality is that they unnecessarily create a longer walking distance and are inappropriate for sidewalks along a street.

Sidewalks should be built along both sides of bridges. Pedestrian rails or guard rail are required along the outside of the bridge. On bridges with high speeds, concrete barriers between the travelway and the sidewalk may be considered to shield pedestrians from errant vehicles. However, this adds cost, weight, and width to the bridge, and the transition from barrier to guard rail or curb at each end often creates an awkward transition for pedestrians, who must detour around the barrier to access the bridge sidewalk.

Rollover curbs should not be used next to sidewalks as they encourage motorists to park on planting strips or sidewalks. They may be problematic for some visually impaired people, since they dont create a definitive edge between the street and adjacent uses.

Sidewalk Depth: Concrete sidewalks should be built to a minimum depth of 101.6 mm (4 in), and to a minimum depth of 152.4 mm (6 in) at driveways.

The actual cost of providing sidewalks will be different for each region of the country and varies with the season. Actual bid prices are also influenced by how busy contractors are at the time of construction.

The cost of constructing sidewalks alone is relatively low; typical bids run between $24 and $36 per meters squared ($20 to $30 a square yard), which roughly translates to $43 to $64 per lineal meter ($12 to $20 per lineal foot) for 1.8-m- (6-ft-) wide sidewalks. Therefore, sidewalks on both sides of the roadway can run roughly between $93,000 and $155,000 per kilometer ($150,000 and $250,000 per mile) (costs from Oregon DOT, 1999).

Factors to consider when calculating the cost of sidewalks:

When project costs appear to be escalating due to one or more of the above-listed items, especially retaining walls or acquiring right-of-way, consideration may be given to narrowing the sidewalk in constrained areas as a last resort. The full sidewalk width should be resumed in non-constrained areasthis is preferable to providing a narrow sidewalk throughout, or dropping the project because of one difficult section.

Tips to Reduce Total Costs:

Read this article:
Pedestrian Safety Guide and Countermeasure Selection System

Related Posts
February 8, 2019 at 6:42 pm by Mr HomeBuilder
Category: Walkways and Steps